Meet the Future of Motor Bearings! Gone are the days of using steel bearings in your motor. This is the very first Ultra High Speed Full Ceramic Motor
Bearings. Stock racers,these
are a must have when you're looking for the best way to achieve maximum
efficiency in your motor. Testing has shown that the
Full Ceramic Bearings
lower the deviation and increase RPM'S in each motor. Also, another benefit is that these bearings are lighter. These bearings
of today's modern brushless motors.Two bearings are included
for both sides of the motor. We recommend using a drop of oil before
use. For those of you
who may not have the tools to replace your bearings we
offer installation as an option as well. Just send your motor to us and we will handle the rest.
Aluminum Timing Ring Screws (3pc)
Use this ultra lightweight fan mount to secure 1 or even 2 fans to your 540 or 550 sized RC motor for optimized cooling.
Clamp type fan mount
Ultra light weight (1.5g)
Can hold up to 2 fans at a time
TECHNOLOGY: 10g OF THRUST AT 8.44 VOLTS OPTIMUM MOTOR COOLING
NO MORE SANDING !!
TKO’s Flat and Finished Lite Diff Rings use our Totally Flat Technology™ to produce the Finest Diff Rings available.These fit most pan cars..12th and 10th scale.
These REPLACE the standard “D” rings.
Using the TKO proprietary process, rings are produced with the specs below.
The faces are flat to within 2 microns and are parallel to within 1 micron with a #7 finish,One micron is 40 millionths of an inch.(.0000040)The rings also fit better and flatter on the hub for near zero run out.
After processing, the rings are checked with an optical flat and monochromatic light. The ultimate measurement for flatness.
Wipe rings with alcohol or motor spray and install.
Short 13mm gold plated - saves weight for TC and 1/12th scale racing (on-road applications)
Short 13mm - the first bullet with copper and silver plating for the best conductivity - saves weight for TC and 1/12th scale racing (on-road applications)
TQ BL sensor cables are made from high quality silicone insulated wire and tube. These units are extremely soft and flexible. They will not tweak 12th scale or pan cars. The silicone wires are burn resistant and crimped at the insulation (not just the conductor) for greater durability. Length is measured between the connectors. We were the first company to create this innovative design for RC - still the least expensive and still the best! In 11 sizes for every electronic layout.
Great for all applications but you must have these if you're running a pan car!
TQ 4mm Low Profile Bullet
The connectors are available in 2 sizes: 18mm and 14mm overall lengths in gold and low resistance silver plate.
The short (14mm) version allows it to fully seat into the battery. This will help resolve issues with some batteries that have a very low profile connector "platform" and will be especially helpful in 12th scale where the the longer bullets could interfere with the body.
These bullets fit all packs but have been redesigned to compress more to provide a better fit in packs that have smaller than usual power connection tubes like RevTech and Reedy batteries.
TQ 1000 is constructed from 1,000 strands of bare copper with a thin wall silicone insulation. Only 3.0mm in diameter, this +/- 14 gauge wire fits right between our 13 gauge and 16 gauge products to provide an alternative for those demanding higher power delivery with great flexibility. 1/12th scale, WGT and Oval pan cars will benefit from the larger conductor while still maintaining a tweak-free chassis for better handling. Available in black.
TQ 16 Gauge wire is constructed with 665 strands of bare copper and thin wall silicone insulation. This wire is only 2.4mm OD, extremely flexible, and absolutely will not tweak 12th and 10th scale pan cars, even with brushless systems that require 3 wires to the motor.
Triple black servo extension cable - Wire "fashionistas" have been asking for these so here you go.....Made with heavy duty 22 gauge conductor, gold plated hardware and triple black insulation. They can handle the hungriest servos but are still very very flexible. 225mm length with JR male and Futaba female or 180mm length with JR or FUT male and tinned ends.
Short servo extension cable - These 10mm extensions can be used as the connector that constantly gets removed when making speedo changes, saving you from abusing the factory cable end and the hassle of replacement. They also allow access to a receiver that's "buried", permitting additional placement options. Available in both JR and Futaba connectors - 24 gauge wires.
Servo cable ends and crimp connectors. 5 sets of JR or Futaba connectors with 15 gold plated/tinned connectors to make your own servo extensions or do repairs
13 Gauge - 1,296 Strand Bare Copper Conductor, Thin Wall Silicon, Extremely Flexible And Only 3.5mm OD.
Our new High Speed Ceramic Diff Balls were designed to hold up to the power of todays brushless motors. These are 1/8th inch and are very high quality and provide a super smooth diff. The diff balls come in a package of 12 to accommodate most spurs.
© 2015-2020 BAM Speed